Automobile News and Information

The purpose of a subwoofer is to add some bass to the audio that is played in the stereo. An already existing factory stereo can be made to play powerful music by adding subwoofer to it. By following these guidelines on how to install a subwoofer in a factory stereo, the installation can be done with little or no help from a professional.

To do the installation of the subwoofer, a wiring kit for amplifier, harness adapter, screwdriver, tool for the removal of the panel, drill, wires, wrench and grommets made of rubber.

The battery of the car is disconnected till the installation is done. The negative terminal cable is removed from the terminal. A screwdriver or an appropriate wrench can be used to loosen it. A ring terminal is attached between the power cable and positive terminal of the battery. The cable for power supply is routed between the compartment where engine is kept and the vehicle’s inner cabin. There is generally an aperture for the wire but if there is no such facility a hole can be drilled and use a grommet for protection.

Before getting into the job first the amplifier kit should be run. It is made to run by connecting it to the battery’ s positive terminal. This step is done easily. They can be made to run through the carpet , by the side of seats and then to the car trunk. This is the power wire. Another wire called remote wire also should be connected to the car trunk. Run it in the same manner as the [power wire and reach the car trunk. The fuse of car lighter or even the car stereo can be used for this connection because as we turn on the car key the amplifier gets switched on.

The connector should always be in contact with the metal portion of the wire so it is sent in to make proper connections. Only the wire for insulation can be allowed to expose out.

The connector is placed in the tool and it is squeezed hard. This is done to make the colour of the crimping tool and the electrical wire same. To ensure a good connection one can choose to do it with a lengthy wire where one can do this kind of work at various places. It is all dependent on the length.

After all connections are made its time to enjoy the sound. People who are deeply passionate about music and powerful sound should make a check of local noise laws for permitted sound level. Another useful tip may be don’t make an attempt to play such loud music before police to show off our new sub woofer installation as we may end up paying fine.

The above were some guidelines on how to install a subwoofer in a factory stereo. The quality of the audio can be improvised by adding a powered or non-powered sub. The above was a discussion of connecting a powered sub. A non powered one can be connected only if the stereo has an amplifier built in the stereo.

Looking to find the best deal on Auto Hifi, then visit www.powernetshop.at to find the best advice on Car audio for you.

Popularity: 1% [?]

Technorati Tags: Bass, cars_and_trucks, factory stereo, install, powernetshop.at, Trucks

For most of us, when we own a car a must-have is a car audio system for our own driving enjoyments as well as for those being driven around. However if you believe that you can derive the maximum enjoyments out of your car audio system merely by owning one and switching it on, you are actually quite wrong as there are many other issues involved for a rounded music experience other than only switching on your car audio system. If you want to experience the best quality of music in your car there are several other features that you need to take care of. Some of us even own those accessories and features and yet do not utilize them to their fullest potential for the best sound quality.

Among the most important accessories that should be installed with your car audio system is also the car audio equalizer which plays a major role in the kind of music that would finally be emanating from your speakers. In simple words, a car audio equalizer regulates the sound and the music from your car audio system; this means that it regulates the various frequencies that occur in sound and music. So in order to derive the best quality of sound that you can from a car stereo system that you surely paid for and had installed all you need to do is fine tune the equalizer and make it compatible with the kind of music you listen to or if you already do not have one you very quickly need to buy one.

Equalizers can either be graphic or parametric. If you are not very familiar with such a device then you should go for a graphic equalizer as it already has some fixed frequencies that you can just change according to your needs. The parametric equalizer is a little tougher to get used to.

There are actually more reasons than just a simple one of fine tuning the frequencies of your sound which make up the reasons why you should get yourself an equalizer for your car audio system but very simply put it would greatly enhance the quality and the kind of sound that you get to hear from your audio system in the car.

In fact there are various kinds of car audio system equalizers that are available in the car audio industry and you should look around for the one that suits you the best. Chances are that you are not very familiar with the device and its features and in this case you should consult an expert in this field who would be able to guide you in acquiring the car audio equalizer. Or you could also do some research for yourself over the internet that would be able to provide you with all the information that you need for buying a car audio equalizer.

Find the best Car Hifi at bargain prices and much more information on Car Audio for the right car stereo.

Popularity: 2% [?]

Technorati Tags: business, car audio, car stereo, cars and trucks, guideline, install, powernetshop.at, shopping, Technology, troubleshooting, Trucks